Why does my Whirlpool washer say F20?

Why does my Whirlpool washer say F20?

Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Why is my Whirlpool washer flashing F?

For instance, the F error code appears in an exceptional case, when the washer doesn’t run at all. It means it neither changes modes nor starts. After being turned on, it doesn’t start any of the programs.

How do you check the pressure switch on a Whirlpool Duet washer?

How to Test the Pressure Switch on a Whirlpool Duet

1. Unplug the Whirlpool Duet washer power cord from the wall outlet.
2. Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver.
3. Adjust the scale on your ohmmeter to the RX1 or X1 scale.

How do I reset my Whirlpool Duet washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

What does f1 mean on a Whirlpool Duet washer?

The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.

What does F code mean on Whirlpool Cabrio washer?

Like other washing machines, Whirlpool Cabrio washer has a set of error codes that indicate specific problems. For instance, the F error code appears in an exceptional case, when the washer doesn’t run at all. It means it neither changes modes nor starts. After being turned on, it doesn’t start any of the programs.

How do you fix the F code on a Whirlpool Cabrio washer?

An F/dL error code indicates a problem with the door lock. The error code will pop up when the door fails to lock. The washer will display the error code after six attempts to lock the door. To fix the issue, the door lock assembly needs to be inspected for loose or broken wires and other signs of damage.

Where is the pressure switch located on a Whirlpool washer?

Locate the pressure switch inside the washer cabinet. From the rear of the washer, the switch will be on the rear left corner of the cabinet. The pressure switch is round with a wiring harness connecting to the back of the switch.

Why is my Whirlpool washer not starting?

If the lid switch is faulty, then the washing machine will not start. It may fill with water but will not spin if the switch is faulty. Some lid switches on top loaders also control the water inlet valve. In some top load washers, if the lid switch is bad, the washer will not fill with water.

What is a F20 error on a whirlpool washing machine?

F20 Error Code. Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error.

How do you wash a whirlpool duet washer?

– Clean the gasket: Spray a rag with mildew cleaner and wipe the gasket, being sure to reach down behind it as well. – Clean the dispensers: Remove the slide-out detergent dispensers and scrub them with soap and water. – Run a “sanitize” cycle: Check the settings on the machine and look for a “sanitize” cycle.

What is Whirlpool washer warranty?

WHIRLPOOL® WASHER WARRANTY. ONE-YEAR FULL WARRANTY For one year from the date of purchase, when this washer is operated and maintained according to instructions attached to or fu rnished with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor costs to correct defects in materials or workmanship.