How do you reset a GPS tracker?

How do you reset a GPS tracker?

How to restart the tracker?

1. Connect the tracker (at least make sure it is loaded) (more information in this article)
2. Press the button firmly for 10 seconds and release (raised and located on the right side, red square below)

How do I reset my GSM GPRS GPS tracker?

6.31 Reset Hardware

1. 6.32 Set up Terminal (local) Time. 6.32.1 Send SMS command “time+space+zone+password+space+time” to the. tracker unit, If succeed, It will reply “time OK”
2. 6.33 TCP / UDP Switch. Send command: “gprs+password,0,0” switch back to TCP mode, this is the. default mode.

What is my GPS password?

Many GPS trackers are shipped with the default password 123456.

How do I restart tracking?

How to reboot my GPS Tracker?

How can I fix my offline GPS?

4 troubleshooting methods for vehicle GPS tracker offline issue

1. Confirm whether the SIM card in the GPS tracking unit is in arrears or has Internet access.
2. The vehicle is in the place where the signal is blind or poor.
3. Method of operation.
4. Solution.
5. Vehicle GPS tracker shutdown or power-down will lead to offline.

How do you put a GPS tracker on a SIM card?

How to configure GPS tracker?

1. Buy SIM card with internet plan.
2. Remove SIM card’s PIN code. Click here to see how to do it on: iOS, Android, Windows Mobile.
3. Insert SIM card in to the GPS Tracker.
4. Configure your GPS Tracker to send data to GPSWOX.COM servers.
5. Your GPS Tracker is ready to send data !

How does a GSM GPS tracker work?

Both GPS tracking and GSM tracking are accomplished by a receiver collecting data from at least 4 satellites in order to determine precise position. GPS GSM tracker devices accomplish this task by referencing information from the cellular tower that is closest to the GSM / GPS tracking device.

How do I reset my GPS password?

Reset Forgot Password Online for Karnataka GPF Account

1. Go to the Accountant General Karnataka website GPF page using agkar.cag.gov.in/agogpf.
2. Click on Already Registered to visit the Login page of Karnataka GPF.
3. Click on the Forgot Password link to open the new page to reset the password.

How do I reset my Aika password?

Enter the e-mail address associated with your account. Click submit to have a password reset link e-mailed to you.

How do I factory reset my charge 2?

How to factory reset a Fitbit Charge 2

1. Attach the Fitbit to its power source, and then start holding down its single button.
2. After two seconds, unplug the USB cable from its port, still holding the button.
3. Count eight seconds, release the button for one second, then press it down again.

Why does my GPS say offline?

What is the cause of vehicle GPS tracker offline issue? It means that the vehicle positioning data cannot be transmitted to the GPS monitoring platform normally, and the current vehicle position information cannot be viewed.

How to reset malfunctioning tk102 tracker?

You can reset malfunctioning TK102 tracker by disconnecting the battery and waiting 10-30 minutes before reconnecting it. Then you can start everything from scratch with the begin123456 command.

What kind of CPU does xexun tk102 have?

NXP is a manufactorer of microcontrollers and processors. The built in CPU of a XEXUN TK102 is usually ARM7 from NXP. And because of that we can use the Flash Magic tool. Download Flash Magic for Windows XP/Vista/7/8/10 here or download Flash Magic Version for MacOS / iOS here.

Does tk102 have any battery protection?

TK102 don’t have any electronics to protect the battery, in our TK102 the battery went wrong in 1 year, we replaced it and the next one also died after a year so now we are using the tracker without battery. TK102 is a low-end device but Xexun and Coban produce acceptable quality for basic tracking.

How to change the SMS map link on the TK-102?

To change the sms map link back to the default text coordinates, send the command “ smstext+password” In configuration software or file of the TK-102 tracker use the following settings to connect it to free GPS tracking system: In order to configure the object, you have to follow these steps by sending SMS commands to the tracker: