What is the command for setting Eigrp?

What is the command for setting Eigrp?

EIGRP configuration commands cheat sheet

Command	Description
Router(config)#router eigrp 20	Enable EIGRP with AS number 20. AS number must be same on all routers to become EIGRP neighbor.
Router(config-router)#network 10.10.0.0	Enable EIGRP on interfaces which belongs to network 10.0.0.0/8. [Classful implementation].

How do I put HP switch into configuration mode?

Configuration commands and the context configuration modes

1. HP Switch(config)# interface c3-c6. HP Switch(eth-C5-C8)#
2. HP Switch(eth-C5-C8)# HP Switch(eth-Trk1)#
3. HP Switch(config)# vlan 100. Command executed at configuration level to enter VLAN 100 context.
4. HP Switch(vlan-100)#
5. HP Switch(vlan-100)#?

How do I setup my HP ProCurve Switch?

How to: Configure a HP ProCurve switch

1. Step 1: Connect your serial connection.
2. Step 2: Conenct PuTTY.
3. Step 3: Get the IP address.
4. Step 4: Set time server.
5. Step 5: Set SNMP community info.
6. Step 6: Launch the web GUI.
7. Step 7: Configure basic info.
8. Step 8: Create VLANs.

How do I conf EIGRP?

To configure EIGRP in the Cisco IOS, just follow these steps:

1. Set the bandwidth on your interfaces using the bandwidth command.
2. Start the EIGRP routing process and specify your AS number.
3. Once you are through this stage, next step is to instruct the router in order to advertise the networks that are directly linked to it.

How do I find my EIGRP configuration?

show ip eigrp interfaces Command Output. The show ip eigrp interfaces command displays information about interfaces configured for EIGRP.

How do I reset my HP ProCurve Switch?

To initialize, or reboot, a ProCurve Switch, perform the following steps:

1. Press the small, recessed Reset button on the face of the switch.
2. Issue the command, reload from within the CLI.
3. Or, issue the command, boot system flash to reboot into either primary or secondary flash.

How do you set up a Procurve switch?

To configure IP addressing. Switch Configuration… If multiple VLANs are configured, a screen showing all VLANs appears instead of the following screen. The Menu interface displays the IP address for any VLAN. If user uses the CLI to configure the IP address on a VLAN, use the CLI show ip command to list them.

How do I log into my Procurve switch?

Log into your ProCurve using SSH or Telnet. Select Run Setup in the menu either by hitting 8 or using the arrow keys then hitting enter. Using the arrow keys, select Logon Default. Hit space to change Logon Default to CLI.

What is the command used to view default IP configuration on a switch?

show switch ip
To display the usability status of configured IP interfaces, use the show switch ip interface command in privileged EXEC mode.

How to configure a HP ProCurve switch?

How to: Configure a HP ProCurve switch Step 1: Connect your serial connection. Connect to the console port of your switch via a serial cable. Older switches… Step 2: Conenct PuTTY. It’s just a standalone .exe with nothing to install. Run PuTTY, and select the ‘serial’ radio… Step 3: Get the IP

Where can I find the HP ProCurve command line interface reference?

• HP ProCurve Command Line Interface Reference – provides a dictionary of CLI commands and syntax. An electronic copy of this reference is included in PDF format on the CD shipped with your HP product, and is also available on the HP ProCurve website.

What is included in the HP ProCurve advanced configuration and management guide?

• HP ProCurve Advanced Configuration and Management Guide – contains advanced configuration information for routing protocols and Quality of Service (QoS). In addition, appendixes in this guide contain reference information for network monitoring, policies and filters, and software and hardware specifications.

How to backup HP ProCurve switch 2524 to Notepad?

All you have to do is copy/paste all (except the first “Running configuration:” line) to notepad on “Backup settings” part to “HP ProCurve Switch 2524#”. If you have set operator and/or manager passwords, don’t copy/paste the lines which start with password.