How much HP can you get out of a 383 Mopar?
The affordable and underrated 383 gets a huge boost in the arm by Muscle Motors—to the tune of 559 hp and 611 lb-ft.
How much horsepower does a 383 Magnum have?
335 hp
The later 383 Magnum (starting in 1968) used the 440 Magnum heads, camshaft, and exhaust manifolds. This engine was advertised at 335 hp (250 kW; 340 PS).
What is the difference between a 383 and a 383 magnum?
there isn’t any outside differences between the 383 and 383 magnum so there isn’t anything to worry about there. big block engines from the factory used a valley pan cover which was also the gasket between the intake and heads and it is held in place by 3 bolts and a plate on the front and rear of the engine.
How much horsepower does a 1969 383 have?
The 1966-1967 383 had a 10:1 compression ratio. The standard issue 4-bbl motor had 325 horsepower. In 1968 and 1969 there were two new high performance versions of the 383 available. The 383 Super Commando was a slight performance upgrade producing 330 hp due to an unsilenced air cleaner and dual exhaust.
How much HP can 383 stroker handle?
The 383 stroker engines have been reported to achieve 330 horsepower with 410 foot-pounds of Torque, 395 horsepower with 410 foot-pounds of Torque and 395 horsepower with 410 foot-pounds of Torque.
Is a 383 Magnum a good motor?
A very good compromise between low RPM velocity and high RPM capacity. Additionally as stated above the 383 has a very good bore/stroke ratio. Compared to say, a 400 smallblock Chevy-the Chevy has heads designed for a 327/350″ displacement motor. Works pretty good but limits high-RPM capability.
Is the Mopar 383 a big block?
The 383 Chrysler B engine is known as the Mopar big block that nobody loves. Typically, gearheads favor its beefier big brother, the 440. The 383 B is characterized by its large cylinder bore of 4.25 inches with a short stroke of 3.375.
What muscle car had a 383 engine?
6 The 1969 Dart GTS 383 With the big roar coming from the dual exhaust, the GTS 383 called plenty of attention to itself. In fact, the Chrysler B-series “big-block” V-8, cast-iron block, and cylinder head has always been a Mopar classic beating heart, making different generation drivers enjoy their muscle car.
Is a Mopar 383 a big block?
Are 383 and 440 same block?
For too many years, the Mopar 383 has been ignored by car crafters blinded by the extra cubes of its cousin, the 440 wedge. The major difference between these two Mopar legends is the deck height of the block: 9.98-inch for the 383 and 10.725-inch for the 440.
Is the 383 a big block?
How much horsepower does a 383 Mopar big block have?
Street/Strip 383 Mopar Big Block Build-up. Stout but hot, our Betty is a 383 short-deck big block whose goal is 600+ horsepower on pump gas, with the ability to inhale a 200-250 horsepower shot of automotive liquid courage, i.e. nitrous oxide. At that point, she’s a bad girl on a hot date in anybody’s book.
How much torque does a 383 have?
A lot of people have never even had a stock stroke 383 built with any sand. They automatically think they are dogs because they are smaller cube engines and nothing could be further from the truth. 350 pound feet of torque can propel a 3400 car deep into the 12s. Maybe faster.
What’s the best carb for 383?
A good Edel. intake and Holley 750 double pumper will fit under the hood. Most people over carb for there build and a 750 for a stock displacement 383 is probably the max. He is going to have to live with a little lope with the cam but a roller hydraulic will have the best street manners and less wear on the engine.
Is a 383 overkill for a 3400 lb car?
A 383 in a 3400 lb car will run pretty nice but an additional 600 lbs will be noticed. And I’m not talking about a stock 400. In stock form, they were mostly dogs. There were a few exceptions tho but not that many. In a house. I get that, but 600 pound feet of torque will certainly be overkill for most things on the street.