How do I reset my Cisco router 2800 to factory settings?

How do I reset my Cisco router 2800 to factory settings?

Method 2

1. xhut the router down.
2. Remove the compact flash from the back of the router.
3. Turn the router back on.
4. When you see the Rommon1> prompt, enter the command of confreg 0x2142.
5. Insert the compact flash.
6. Type reset.
7. When prompted to enter the initial configuration, type no and press enter.

How do I clear all settings on a Cisco router?

Clear the configuration of your switch

1. Log on to your switch, and enter the privileged EXEC mode by entering enable and then entering the enable password command.
2. Enter clear config all to reset the entire system. You don’t need to reload the switch because processing the command wipes the switch.

How do I reset my Cisco router to factory default?

Reset Router Using Reset Button Find the Reset button on the router. Press and hold the Reset button while you power on the router. Release the Reset button after 10 seconds. Wait 5 to 10 minutes for the router to finish booting.

How do I reset my Cisco 2960x to factory settings?

Press and hold the front panel MODE button, and power-up the switch. – After a few seconds, the following should display. Release the MODE button.

Where is the Reset button on a Cisco 2800?

The default username is cisco and the default password is cisco. Step 1. Press the Reset button located at the back of the device with a pin for approximately 15 seconds or until the power light on the front of the device starts flashing. The Router reloads and is set to the default configuration settings.

How do I restore a Cisco switch to factory settings?

Resetting the Cisco IP switch to factory defaults

1. Reset the switch to factory defaults: Erase the existing configuration: write erase. Reload the switch software: reload.
2. Save the configuration: IP_switch-A-1# copy running-config startup-config.
3. Reboot the switch and wait for the switch to reload: IP_switch-A-1# reload.

How do I reboot my Cisco router?

Press the Break1 key during the first 60 seconds while the system is booting. 1. This key will not work on the Cisco 7000 unless it has at least Cisco IOS Release 10 boot ROMs.

Where is Cisco router Reset button?

Press the Reset button located at the back of the device with a pin for approximately 15 seconds or until the power light on the front of the device starts flashing. The Router reloads and is set to the default configuration settings.

How do I factory RESET my router?

How to Reset Router From Configuration Page

1. Type your router’s IP address into any web browser’s search field.
2. Enter your username and password when prompted.
3. Go to System or System Tools.
4. Look for Restore or Factory Default.
5. Click Restore or Reset and OK to confirm.
6. Wait for the router to reboot.

How do I reset a Cisco router to factory default settings?

The router is now reset to the original factory defaults. This method uses the config-register 0x2142 command in global configuration mode. Enter the config-register 0x2142 command in global configuration mode. This causes the router to ignore the start-up configuration on the next reload.

How to enable ROM monitor on the Cisco 2500 Series router?

Break the boot sequence when powering on the Cisco 2500 Series router to place yourself in rom monitor mode. Change the configuration register to 0x2142 to make the router bypass the contents of NVRAM when booting then initialize the router (boot the router into IOS)

What to do if your Cisco 2500 router has an unknown console?

A Cisco 2500 Series router that has an unknown console or enable password. An active Serial Console session to the device that you’re unable to login to. Break the boot sequence when powering on the Cisco 2500 Series router to place yourself in rom monitor mode.

What is the most common use for the Cisco 2500 Series router?

The most common use for the Cisco 2500 Series Router (s) are for training purposes; commonly used in lab environments, the 2500 series router makes a great introductory router to the Cisco IOS (Internetwork Operating System). A Cisco 2500 Series router that has an unknown console or enable password.