What does E1 mean on a Whirlpool Duet dryer?
Thermistor Failure
Whirlpool E1, E2 – Thermistor Failure This error code is indicating that the exhaust air temperature is either below 18 degrees Fahrenheit or above 250 degrees Fahrenheit. Check the thermistor with an Ohm meter, if it reads >50k Ohms (E1) or less than 500 Ohms (E2) it is defective.
What does E1 mean on dryer?
open thermistor
“E1” on that model dryer does indicate an open thermistor (solid state temperature sensor) which as you can see below is not that expensive of a part.
How do you clear the error code on a Whirlpool Duet dryer?
Press the “Pause/Cancel” button on the control panel twice to clear the error. Contact a certified repair technician if pressing the “Pause/Cancel” button does not clear the error, as this indicates that a component has failed in the washing machine or dryer.
What does E1 F1 mean on Whirlpool washer?
The Whirlpool Washer F1E1 error means the ACU (main control board) memory is corrupted or another critical ACU failure has occurred. It’s possible that a power surge or a drop in voltage caused the issue. Unplug the washer for 1 minute and plug it back in.
What does E1 f1 mean on Whirlpool washer?
Does a Whirlpool Duet dryer have a reset button?
Whirlpool dryers can do many things, such as monitor moisture levels and temperature, reduce noise, periodically tumble clothes to remove wrinkles, steam clothes and adjust the overall drying time according to fabric and load size. However, one thing a Whirlpool dryer cannot do is reset itself by pushing a button.
What does F1 mean on a Whirlpool dryer?
Whirlpool dryer also displays f1 error code if the wires going to the central module have an opening or unstable contact.
What does E1 mean?
Summary of Key Points
| E1 | |
|---|---|
| Definition: | Everyone |
| Type: | Abbreviation |
| Guessability: | 4: Difficult to guess |
| Typical Users: | Adults and Teenagers |
What does code F1 mean on Whirlpool dryer?
To recap, the cause of the Whirlpool Cabrio dryer F1 error code is a miscommunication between the control board and the rest of the machine. Check for any loose or damaged wires. If no loose or damaged wires are found, replace the control board and this should clear up your problem.
How to reset a whirlpool duet dryer?
Step One: Inspect Your Power Source. The first step in tackling a troubleshooting or reset issue is inspecting your household’s circuit breaker or fuses.
How do you clean a whirlpool duet dryer?
How to Clean Whirlpool Gas Dryer Vents & Lint Traps. Remove the screws securing the round, metal vent from the back of the dryer, using a nut driver or screwdriver. Pull the vent off of the dryer vent outlet. Insert the dryer lint brush into the vent as far as it will go. Move the brush around and from side-to-side. Pull the brush out. Do this several times until there is no more lint on the brush.
What are the Whirlpool duet washer error codes?
Some of the error codes that appear on a Whirlpool Duet include error code “F/H,” which means there is no water detected; error code “F/02,” which means draining takes more than 8 minutes; and error code “F/05,” which means there’s an error in the water temperature sensor.
What is the E1 error code for the Whirlpool?
A Whirlpool Washer displays a F5 E1 error code when a Door or Lid Switch Error has been detected by the internal electronic diagnostics. This code appears if the control does not detect the door opening after 3 consecutive loads, indicating that the door switch failed. The code also displays when the door switch is open with the door locked.