What are the safety features on a band saw?
A blade-braking mechanism provided to automatically stop power to the band saw motor upon blade breakage.
What is a band saw guard?
Made of clear acrylic, guards attach to your band saw blade’s support arm at an angle to minimize glare. Made of clear acrylic, guards attach to your band saw blade’s support arm at an angle to minimize glare.
Do band saws need guards?
Bandsaws must be guarded. Guarding must prevent access to the bandsaw blade but still allow the employee to see the material being cut. A push stick allows employees to keep fingers and hands clear of the blade.
When operating a bandsaw Which of the following is a safe practice?
Keep guards in place at all times. The blade guard should be from 1/8 to ¼ inch above stock. Keep hands away from blade and do not open upper or lower bandsaw doors while blade is in motion. Maintain a balanced stance and keep your body under control at all times; do not overreach.
What is the number 1 safety rule of the band saw?
Safety Rules Never clear small pieces while blade is moving. Never adjust saw or setup while saw is running. Never cross arms. Always follow 4 inch rule.
What is the margin of safety on a band saw?
4”
Always maintain a 4” margin of safety. If it is necessary to back the saw out of a long cut, turn the power off and wait for the blade to stop.
What is the criteria for a guard having to be used on a machine?
Machine safeguards must meet these minimum general requirements: Prevent contact: The safeguard must prevent hands, arms or any other part of a worker’s body from contacting dangerous moving parts. Be secure: Workers should not be able to easily remove or tamper with the safeguard.
How does OSHA define guarded by location?
1917.151(a) Definition. “Guarded” means shielded, fenced, or enclosed by covers, casings, shields, troughs, spillways or railings, or guarded by position or location.
What side of the bandsaw should you never stand on?
right
Cutting cylindrical or irregular stock on the band saw may be done only with a special jig, such as a V-block (special setup). Never stand or allow others to stand to the right of the band saw when it is running.
What are 5 general guidelines for using the band saw?
What safety procedures should you follow when using a band saw?
- Wear safety glasses or goggles, or a face shield (with safety glasses or goggles).
- Wear hearing protection that is suitable for the level and frequency of the noise you are exposed to in the woodworking area.
- Wear protective footwear when required.
What should you never cut on a bandsaw?
Always adjust the speed of the band saw while the machine is running. Never adjust the speed with the machine turned off. Never cut materials that might be hardened, such as tool steel, files, hardened guideways, stainless steel etc.
Is it safe to cut large diameter cylindrical material on the band saw?
Cutting cylindrical or irregular stock on the band saw may be done only with a special jig, such as a V-block (special setup). Never stand or allow others to stand to the right of the band saw when it is running. If you hear a clicking noise, turn off the saw at once.
What are the safety features of a band saw?
Blade guards which are installed by the band saw designers is one of the most crucial band saw safety features. Blade guards are installed to prevent any finger-cut or hand-cut due to unintentional or unwary movement while the blade is running.
How do I mount the band saw safety guard?
The band saw safety guard can mount to the front door using the supplied bracket, or side of the upper housing. Constructed from 28mm industrial aluminum extrusion Slotted aluminum allows adjustment in/out and up/down to clear the work-piece and guard the vertical band saw blade at different heights. Steel adjustable lever for easy re-positioning
How do you stop a band saw from restarting?
Check out our printable Band Saw Safety Guide. Install an interlocked motor brake to stop the blade quickly after each operation [OSHA 1910.212 (a) (1)]. Install accidental restart prevention [1910.213 (b) (3]. Install an ANSI-compliant emergency stop button [NFPA 79].
How do I use the makesafe power tool brake?
The MAKESafe Power Tool Brake is a plug-and-play braking solution that also includes anti-restart and emergency stop. All you have to do is plug it in, perform a calibration that takes less than five minutes, and you’ve added multiple machine safeguards to your band saw. See the product demonstration video and specifications for more information.